HTML5 Webook

221/248

VariousTypesofWaterEqupment■WOC-13H■WOC-13Rofii2 VariousTypesWaterEqupmentModel code structureWNH3/8-2XModel code structureWOC-13R■ Specifications■ Specifications70 MPa High-Pressure Nylon Hoses70 MPa Water CouplersX:With WOC-13H on one side XW:With WOC-13H on both sidesY:With WS-1H on one side YW:With WS-1H on both sidesNC:No couplersR:Cylinder side couplerH:Hose side coupler13:3/8 (WOC) 1:3/8 (WS) WOC:One-touch couplerWS:Standard coupler ● Do not hold a water high-pressure nylon hose while pressure is applied. If the hose is broken while held by hand, the high-pressure water could spurt and cause severe injury, for example, a pierced hand. ● Before work starts, check the following: damage to the hose, swelling of the hose (sheath), exposure of the reinforced layer (external damage), bent (deformation), leakage from the joints, etc. If any of the above problems is found, replace the hose with new one immediately because the use of a damaged hose is dangerous. Even if there are no abnormalities in appear-ance, there may be scratches, pinholes, etc. inside the hose. Replace the hose regularly taking the operating conditions into account. Various Types of Water EquipmentNote 1. The operating temperature range shown above can be applied to the hose alone.Note 2. The approx. weight represents the weight of the hose alone. It does not include the joints at both ends and the protection.● Pressure must not be applied to a WS-1 series coupler alone. Otherwise,　the equipment may be damaged. ● It is dangerous to connect or disconnect the couplers while pressure is　applied. Doing so may allow compressed water to flow out, causing injury. ● Securely and completely connect the couplers. Not doing so could cause　pressure not to rise, the hydraulic fluid not to flow, or other problems. ● If the pressure fluctuates often or vibration is transmitted to the couplers,　regularly check the looseness of the cap nut. ● If a cylinder that works normally with WS-1 series couplers stops suddenly,　the most likely cause is looseness (a gap) between the couplers. Tighten the couplers again using a tool if a gap exists. ● A duster cap is included with a coupler. Attach the cap to the coupler after　use to prevent dust.● Can be used at working pressures up to 70 MPa with tap water as the　hydraulic fluid. ● The joints are made of stainless steel. ● The standard overall length is 2 m. Hoses having an overall length other　than 2 m can be manufactured. (Make-to-order products)*For precautions for and maintenance of water high-pressure nylon hoses, see page 179. *Water high-pressure nylon hoses with couplers at both ends are not filled with hydraulic fluid. Use the hose after air vent. ■WNH3/8-2NCMaximumoperating pressure MPaModelWNH3/870● Can be used at working pressures up to 70 MPa with tap water as the　hydraulic fluid. ● Equipped with a lock mechanism to prevent detachment. (WOC only)Maximum operating pressureMPaModelWOC-13RWOC-13HWS-1RWS-1H70 ■WOC-13R ■WOC-13H ■WS-1R ■WS-1HOverall length (m)Thread sizeWater high-pressure nylon hoseThread sizeWater couplerAttached coupler■WNH3/8Threadsize RMaterialNylon3/8Operating fluid temperature range°CApprox. weightkg0.10.150.130.120 to 505 to 50No.79E since2025Operatingtemperature range °CHydraulicfluid0 to 50(Note 1)Tap waterHydraulic fluidTap water■WS-1RStandardoverall length mExpansionvolume cm3/mVolumecm3/m31.24.8■Hydraulic symbol (coupled couplers) Accessory(duster cap)WOC-13R-DCWOC-13H-DCS-1R-DCS-1H-DC■WS-1HMinimumbend radius mmApprox. weightkg/m550.21(Note 2)220