tnempuqEesUlaiitiiiiSilABR125S34 cepSrof■EMP-5RCS electric circuit diagram ■EMP-5RCS12ERST■RC-70/100■RC-20/35/50■RC-10■Wiring diagrampuoChcnuPhcnuPretsaMtroPsdnaSsserPdradnatSsdnatSsserPsrenosneTtloBllsrellilnMuPgniraeBuPgnsgnhcnuPsrettuCebaCsresrettuCdoRsrenethgartPower supply0.75kW 4PPressure switchPower supplyBKDPGS-70WTMCTHMotor startDirection-controlvalveActiveSOL11MCTHPL(WH)Activation switchOn/OffSSRDCRBLPSCRSwitched-mode power supplyDC24V 15WSWCR10121012Electrical receptacle for operation switchNJW-202-RF(NANABOSHI ELECTRIC Mfg Co.,Ltd)■ SpecificationsMake-to-order product Rod CuttersSpecial Pumps for Straighteners and Rod CuttersElectric pumpEMP-5:EMP-5 modelNo.18Pressure switch22Direction-control valveESL-4S-227Air breather29Oil level gauge34Oil drain port35Return port36Outlet port40Mover’s dolly41Receptacle10:100kN20:200kN35:350kN50:500kNHV:With 3-way hand valve 70:700kNSW:With hand switch 100:1000kN (Make-to-order product )VCT operating cable : 1.25mm2 X 2C 0.5mMP-10:MP-10 modelMP-15:MP-15 modelAC200/220V 50/60HzRCS:Single-operation RCW:Dual-operation Tank port *(Rc1/2)OutputCutting capacityTensile strength1000 N/mm2ϕ 13 max.ϕ 18 max.ϕ 25 max.ϕ 30 max.ϕ 35 max.ϕ 42 max.kN100200350500700100070Rod cutterTank port *(Rc1/2)(HV-120VC)Hand swich (SW-220VC)Attached couplerVC:With VC-70-R3Tank port *(Rc1/2)(HV-120VC)Hand swich (SW-220VC)Rod Cutters(HV-110VC)Hand swich (SW-210VC)*The performance of each pump is the same as that of the standard model. See page 80 (EMP-5), page 82 (MP-10), and page 86 (MP-15).Required oil volumecm32270154234397704No.79E since2025Approx. weightkg■Hydraulic symbol(3-way hand valve )258.5348419459585733(16)(22)(32)(34)(40)(50)7.517.5265070136 (SW hand switch)VCT operating cable : 1.25mm2 X 2C 0.5mVCT operating cable : 1.25mm2 X 2C 0.5mNameNotes1Oil tank4Motor6Activation switch7Pilot lamp DPGS-70Rc3/8Rc3/8Rc3/8For remote controlled operating switchModel code structureModel code structureMP-10● Can cut carbon steel bars, special steel bars, and so on. It is designed to prevent the blades from contacting each other. *Because the cutter may chip due to metal fatigue, be sure to wear protective goggles during work.■RC-10-SWVCMaximum operating pressureMPaModelRC-10-HV(SW)RC-20-HV(SW)RC-35-HV(SW)RC-50-HV(SW)RC-70-HV(SW)RC-100-HV(SW)* Do not attach the coupler to the tank port, instead attach the low-pressure hose directly to the tank port.● Special pumps for the SW models of straighteners and rod cut-ters. There are two types: one is the single-use type (RCS model) that can use a straightener or a rod cutter, the other is the combined-use type (RCW model) that has two outlet ports for a straighteners and rod cutters.● Pay attention to the cylinder speed if a 40 kN or 100 kN cylinder is used. The SMP series or a one-stage electric pump may be able to be used as a replacement. Please contact us for details. 195RCSRC-10-HVVC
元のページ ../index.html#196